1

我正在尝试制作一个从 0 到 9 计数并显示在 Nexys A7 的七段显示器上的计数器。代码可以编译，但在测试平台中显示所有输出都是未知的。我测试了我的时钟分频器模块，它看起来不错。我不确定为什么它不起作用。

module BCD_sevenseg(
    input clk,
    output segA, segB, segC, segD, segE, segF, segG, segDP, div_clk
    );
    
    counter module1(
    .clk(clk),
    .div_clk(div_clk)
    );
    
    reg[3:0] BCD; //BCD signal is 4 bits wide
    always@(posedge clk) //check every positive edge
        if(div_clk) //executes if counter value from module1 is true
            BCD <= (BCD == 4'h9 ? //check if BCD is at binary 9
            4'h0 : BCD + 4'h1 );
            //true: reset to 0
            //false: count up
     
    reg [7:0] sevenseg; //8 segments on 7 segment display (w/ decimal point)
    always@(*)
    case(BCD) //one case for each digit
        4'h0: sevenseg = 8'b11111100;
        4'h1: sevenseg = 8'b01100000;
        4'h2: sevenseg = 8'b11011010;
        4'h3: sevenseg = 8'b11110010;
        4'h4: sevenseg = 8'b01100110;
        4'h5: sevenseg = 8'b10110110;
        4'h6: sevenseg = 8'b10111110;
        4'h7: sevenseg = 8'b11100000;
        4'h8: sevenseg = 8'b11111110;
        4'h9: sevenseg = 8'b11110110;
        default: sevenseg = 8'b00000000;        
    endcase
    
    assign {segA, segB, segC, segD, segE, segF, segG, segDP} = sevenseg;
    
endmodule

时钟分频器：

module counter(
    input clk,
    output reg div_clk=0
    );

integer count_value=0;

always@(posedge clk)
begin
    if(count_value == 10)//change this number to adjust output signal frequency
    begin
        div_clk = ~div_clk;
        count_value <= 0;
    end
    else
        count_value <= count_value+1;
end


endmodule

测试台代码：

module BCD_sevenseg_tb();

reg clk=0;
wire segA, segB, segC, segD, segE, segF, segG, segDP, div_clk;


BCD_sevenseg UUT(
.clk(clk),
.segA(segA),
.segB(segB),
.segC(segC),
.segD(segD),
.segE(segE),
.segF(segF),
.segG(segG),
.segDP(segDP),
.div_clk(div_clk)
);

always
#1 clk=~clk;
    
endmodule

测试台截图

4

1 回答 1

0

您的输出始终为 X，因为BCD始终为 X。您声明BCD为 a reg，默认为 X。您需要初始化BCD为已知值，例如 0。

出于模拟目的，您可以简单地执行此操作：

reg[3:0] BCD = 0; //BCD signal is 4 bits wide

初始化信号的标准方法是使用复位输入信号。例如：

always @(posedge clk) begin
    if (reset) begin
        BCD <= 4'h0;
    end else begin
        if (div_clk) BCD <= (BCD == 4'h9 ? 4'h0 : BCD + 4'h1 );
    end
end
于 2020-10-13T18:57:00.097 回答