0

这里代码一些警告，但没有发现错误，但是这个全加法器输出波形和的测试台和进位没有显示。在进位和求和输出中显示了你，但不是输入很好，只有求和和进位输出是问题原因，这里有一些警告，有时我对那个警告有疑问，这里我附上你的图片作为参考并给我一些建议来解决这个问题。在此处输入图像描述

 -- 1-bit full adder testbench
 -- A testbench is used to rigorously tests a design that you have made.
 -- The output of the testbench should allow the designer to see if
 -- the design worked. The testbench should also report where the testbench
 -- failed.
  LIBRARY IEEE;
  use IEEE.STD_LOGIC_1164.ALL;
  -- Declare a testbench. Notice that the testbench does not have any input
 -- or output ports.
entity tb_1bitfulladder is
end tb_1bitfulladder;
 -- Describes the functionality of the tesbench.
 architecture MY_TEST of tb_1bitfulladder is
 -- The object that we wish to test is declared as a component of
 -- the test bench. Its functionality has already been described elsewhere.
 -- This simply describes what the object's inputs and outputs are, it
 -- does not actually create the object.
     component FULL_ADDER
      port( x, y, Cin : in STD_LOGIC;
       s, Cout : out STD_LOGIC );
     end component;
     -- Specifies which description of the adder you will use.
     --for U1: FULL_ADDER use entity WORK.FULL_ADDER(MY_DATAFLOW);
     -- Create a set of signals which will be associated with both the inputs
     -- and outputs of the component that we wish to test.
    signal X_s, Y_s : STD_LOGIC:='0';
    signal CIN_s : STD_LOGIC:='0';
    signal SUM_s : STD_LOGIC;
    signal COUT_s : STD_LOGIC;
    -- This is where the testbench for the FULL_ADDER actually begins.
  BEGIN
   -- Create a 1-bit full adder in the testbench.
    -- The signals specified above are mapped to their appropriate
     -- roles in the 1-bit full adder which we have created.
  UUT: FULL_ADDER port map (x=>X_s,       --(//this line has some warning i put it below END Othecode)
                         y=>Y_s,
                         Cin=>CIN_s,
                         s => SUM_s, 
                         Cout=> COUT_s
);
  -- The process is where the actual testing is done.       
  -- stimulus process
   stim_proc:process
      begin
  -- We are now going to set the inputs of the adder and test
  -- the outputs to verify the functionality of our 1-bit full adder.
  -- Case 0 : 0+0 with carry in of 0.
  -- Set the signals for the inputs.
   X_s <= '0';
   Y_s <= '0';
   CIN_s <= '0';
 -- Wait a short amount of time and then check to see if the
 -- outputs are what they should be. If not, then report an error
  -- so that we will know there is a problem.
  wait for 10 ns;

  assert ( SUM_s = '0' ) report "Failed Case 0 - SUM" severity error;
  assert ( COUT_s = '0' ) report "Failed Case 0 - COUT" severity error;
  wait for 40 ns;
   -- Carry out the same process outlined above for the other 7 cases.
   -- Case 1 : 0+0 with carry in of 1.
   X_s <= '0';
   Y_s <= '0';
   CIN_s <= '1';
   wait for 10 ns;
   assert ( SUM_s = '1' ) report "Failed Case 1 - SUM" severity error;
   assert ( COUT_s = '0' ) report "Failed Case 1 - COUT" severity error;
   wait for 40 ns;
-- Case 2 : 0+1 with carry in of 0.
   X_s <= '0';
   Y_s <= '1';
   CIN_s <= '0';
   wait for 10 ns;
   assert ( SUM_s = '1' ) report "Failed Case 2 - SUM" severity error;
   assert ( COUT_s = '0' ) report "Failed Case 2 - COUT" severity error;
   wait for 40 ns;
  -- Case 3 : 0+1 with carry in of 1.
   X_s <= '0';
   Y_s <= '1';
  CIN_s <= '1';
  wait for 10 ns;
  assert ( SUM_s = '0' ) report "Failed Case 3 - SUM" severity error;
  assert ( COUT_s = '1' ) report "Failed Case 3 - COUT" severity error;
  wait for 40 ns;
 -- Case 4 : 1+0 with carry in of 0.
  X_s <= '1';
  Y_s <= '0';
 CIN_s <= '0';
 wait for 10 ns;
 assert ( SUM_s = '1' ) report "Failed Case 4 - SUM" severity error;
 assert ( COUT_s = '0' ) report "Failed Case 4 - COUT" severity error;
 wait for 40 ns;
 -- Case 5 : 1+0 with carry in of 1.
  X_s <= '1';
  Y_s <= '0';
  CIN_s <= '1';
  wait for 10 ns;
  assert ( SUM_s = '0' ) report "Failed Case 5 - SUM" severity error;
  assert ( COUT_s = '1' ) report "Failed Case 5 - COUT" severity error;
  wait for 40 ns;
  -- Case 6 : 1+1 with carry in of 0.
   X_s <= '1';
   Y_s <= '1';
   CIN_s <= '0';
   wait for 10 ns;
    assert ( SUM_s = '0' ) report "Failed Case 6 - SUM" severity error;
    assert ( COUT_s = '1' ) report "Failed Case 6 - COUT" severity error;
   wait for 40 ns;
  -- Case 7 : 1+1 with carry in of 1.
   X_s <= '1';
   Y_s <= '1';
   CIN_s <= '1';

   wait for 10 ns;
  assert ( SUM_s = '1' ) report "Failed Case 7 - SUM" severity error;
  assert ( COUT_s = '1' ) report "Failed Case 7 - COUT" severity error;
  wait for 40 ns;
  end process;
END MY_TEST;

Warning: ELAB1_0026: tb_1bitfulladder.vhd : (35, 0): There is no default binding for component     "FULL_ADDER". (No entity named "FULL_ADDER" was found).
4

0 回答 0