1

我在Github上找到了这个很棒的库其中包含将 MPU-6050 陀螺仪/加速度计与 arduino 一起使用的链接，他在那里有一个示例，他将其用于 esp 模块和普通的 arduino。esp 库对我不起作用，但在我找到 github 的教程中，他们显示名为“MPU6050_DMP6_using_DMP_V6.12”的库正在工作。由于我无法修复 esp 的库，并且我无法在线找到另一个使用此模块并实现我的 janky-VR 控制器项目所需的中断键的库，我想知道是否有办法编辑代码前面提到的草图与 esp 一起工作。我对旧的 esp 草图的问题是，即使我的波特率在所有东西上都是正确的，串行监视器也没有任何显示。也许如果你们能想出一种方法来实现它以与 esp 一起工作，那将是惊人的，因为我无法弄清楚他的代码。这是一个我设法显示到串行但不使用中断键的项目，如果这可能有帮助的话。

#include <Wire.h>

// MPU6050 Slave Device Address
const uint8_t MPU6050SlaveAddress = 0x68;

// Select SDA and SCL pins for I2C communication 
const uint8_t scl = D6;
const uint8_t sda = D7;

// sensitivity scale factor respective to full scale setting provided in datasheet 
const uint16_t AccelScaleFactor = 16384;
const uint16_t GyroScaleFactor = 131;

// MPU6050 few configuration register addresses
const uint8_t MPU6050_REGISTER_SMPLRT_DIV   =  0x19;
const uint8_t MPU6050_REGISTER_USER_CTRL    =  0x6A;
const uint8_t MPU6050_REGISTER_PWR_MGMT_1   =  0x6B;
const uint8_t MPU6050_REGISTER_PWR_MGMT_2   =  0x6C;
const uint8_t MPU6050_REGISTER_CONFIG       =  0x1A;
const uint8_t MPU6050_REGISTER_GYRO_CONFIG  =  0x1B;
const uint8_t MPU6050_REGISTER_ACCEL_CONFIG =  0x1C;
const uint8_t MPU6050_REGISTER_FIFO_EN      =  0x23;
const uint8_t MPU6050_REGISTER_INT_ENABLE   =  0x38;
const uint8_t MPU6050_REGISTER_ACCEL_XOUT_H =  0x3B;
const uint8_t MPU6050_REGISTER_SIGNAL_PATH_RESET  = 0x68;

int16_t AccelX, AccelY, AccelZ, Temperature, GyroX, GyroY, GyroZ;

void setup() {
  Serial.begin(9600);
  Wire.begin(sda, scl);
  MPU6050_Init();
}

void loop() {
  double Ax, Ay, Az, T, Gx, Gy, Gz;

  Read_RawValue(MPU6050SlaveAddress, MPU6050_REGISTER_ACCEL_XOUT_H);

  //divide each with their sensitivity scale factor
  Ax = (double)AccelX/AccelScaleFactor;
  Ay = (double)AccelY/AccelScaleFactor;
  Az = (double)AccelZ/AccelScaleFactor;
  T = (double)Temperature/340+36.53; //temperature formula
  Gx = (double)GyroX/GyroScaleFactor;
  Gy = (double)GyroY/GyroScaleFactor;
  Gz = (double)GyroZ/GyroScaleFactor;

  Serial.print("Ax: "); Serial.print(Ax);
  Serial.print(" Ay: "); Serial.print(Ay);
  Serial.print(" Az: "); Serial.print(Az);
  Serial.print(" T: "); Serial.print(T);
  Serial.print(" Gx: "); Serial.print(Gx);
  Serial.print(" Gy: "); Serial.print(Gy);
  Serial.print(" Gz: "); Serial.println(Gz);

  delay(100);
}

void I2C_Write(uint8_t deviceAddress, uint8_t regAddress, uint8_t data){
  Wire.beginTransmission(deviceAddress);
  Wire.write(regAddress);
  Wire.write(data);
  Wire.endTransmission();
}

// read all 14 register
void Read_RawValue(uint8_t deviceAddress, uint8_t regAddress){
  Wire.beginTransmission(deviceAddress);
  Wire.write(regAddress);
  Wire.endTransmission();
  Wire.requestFrom(deviceAddress, (uint8_t)14);
  AccelX = (((int16_t)Wire.read()<<8) | Wire.read());
  AccelY = (((int16_t)Wire.read()<<8) | Wire.read());
  AccelZ = (((int16_t)Wire.read()<<8) | Wire.read());
  Temperature = (((int16_t)Wire.read()<<8) | Wire.read());
  GyroX = (((int16_t)Wire.read()<<8) | Wire.read());
  GyroY = (((int16_t)Wire.read()<<8) | Wire.read());
  GyroZ = (((int16_t)Wire.read()<<8) | Wire.read());
}

//configure MPU6050
void MPU6050_Init(){
  delay(150);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_SMPLRT_DIV, 0x07);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_PWR_MGMT_1, 0x01);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_PWR_MGMT_2, 0x00);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_CONFIG, 0x00);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_GYRO_CONFIG, 0x00);//set +/-250 degree/second full scale
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_ACCEL_CONFIG, 0x00);// set +/- 2g full scale
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_FIFO_EN, 0x00);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_INT_ENABLE, 0x01);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_SIGNAL_PATH_RESET, 0x00);
  I2C_Write(MPU6050SlaveAddress, MPU6050_REGISTER_USER_CTRL, 0x00);
}

编辑：这是我使用的板设置以及“MPU6050_DMP6_ESPWiFi”示例

4

1 回答 1

1
  1. 使用I2C_Scanner示例检查 I2C 接口是否工作。这将返回连接的 I2C 设备的地址。如果 Address 返回，则确认 I2C 正在工作。
  2. 检查是否连接了上拉电阻。
  3. 您可以重新确认您的串行连接。只需评论Wire.begin(sda, scl); 称呼。
  4. 尝试使用默认的 i2c 引脚。
于 2020-04-17T03:03:49.457 回答