4

我正在尝试为称为 uLCD32-pt 的 LCD 设备编写脚本，问题是您需要以 9600 的波特率连接到它，并且为了获得更高的波特率，您必须连接到它，发送更改波特率命令，然后以新设置的波特率发送新命令。我的液晶显示器在绘制像素时变得非常慢，我知道这是因为波特率，所以他们有什么方法可以在连接到设备后改变波特率？到目前为止，这是我的代码吗？

import serial
import time

#Connect to uLCD32-pt with autobaud
ser = serial.Serial(
    port='/dev/ttyUSB0', 
    baudrate=9600, 
    timeout=1,
    parity=serial.PARITY_NONE,
    stopbits=serial.STOPBITS_ONE,
    bytesize=serial.EIGHTBITS
)
ser.write("U")


while(True):
    #15 x white pixels
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0001)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#1
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0002)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#2
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0003)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#3
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0004)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#4
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0005)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#5
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0006)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#6
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0007)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#7
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0008)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#8
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0009)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#9
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x000A)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#10
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x000B)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#11
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x000C)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#12
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x000D)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#13
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x000E)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#14
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x000F)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#15
    ser.write(chr(0x0050)+chr(0x0000)+chr(0x0010)+chr(0x0000)+chr(0x000A)+chr(0x00FF)+chr(0x00FF))#16
4

2 回答 2

9

在文档中，波特率属性的描述说：

读取或写入当前波特率设置。

所以我希望这条线可以工作：

ser.baudrate = 115200
于 2012-02-14T04:50:07.097 回答
6

如果端口已经打开，您可以调用setBaudrate它进行一些检查并重新配置端口。

ser.setBaudrate(115200)
于 2014-04-01T14:01:32.867 回答