使用 LODSB 将相对地址加载到我的代码中的字符串所需的最少步骤是什么?
我有以下使用 PXE 引导的测试程序。我通过两种方式启动它:通过 pxelinux.0 和直接。如果我直接启动它,我的程序会打印两个字符串。如果我通过 pxelinux.0 启动,它只会打印第一个字符串。
为什么?
答: 代码没问题,初始地址数学错误。见下文。
工作技术(两者):
- 将方向标志设置为递增,
cld
- 设置
ds
为cs
- 将字符串的地址(从开始)放入
si
- 将起始偏移量添加到
si
非工作技术(仅适用于 pxelinux):
- 计算一个新的段地址
(((cs << 4) + offset) >> 4)
- 设置
ds
为。(A000 或 07C0)
// Note: If you try this code, don't forget to set
// the "#if 0" below appropriately!
.text
.globl start, _start
start:
_start:
_start1:
.code16
jmp real_start
. = _start1 + 0x1fe
.byte 0x55, 0xAA
// Next sector
. = _start1 + 0x200
jmp real_start
test1_str:
.asciz "\r\nTest: 9020:fe00"
test2_str:
.asciz "\r\nTest: a000:0000"
real_start:
cld // Make sure %si gets incremented.
#if 0
// When loaded by pxelinux, we're here:
// 9020:fe00 ==> a000:0000
// This works.
movw $0x9020, %bx
movw %bx, %ds
movw $(test1_str - _start1), %si
addw $0xfe00, %si
call print_message
// This does not.
movw $0xA000, %bx
movw %bx, %ds
movw $(test2_str - _start1), %si
call print_message
#else
// If we are loaded directly without pxelinux, we're here:
// 0000:7c00 ==> 07c0:0000
// This works.
movw $0x0000, %bx
movw %bx, %ds
movw $(test1_str - _start1), %si
addw $0x7c00, %si
call print_message
// This does, too.
movw $0x07c0, %bx
movw %bx, %ds
movw $(test2_str - _start1), %si
call print_message
#endif
// Hang the computer
sti
1:
jmp 1b
// Prints string DS:SI (modifies AX BX SI)
print_message:
pushw %ax
jmp 2f
3:
movb $0x0e, %ah /* print char in AL */
int $0x10 /* via TTY mode */
2:
lodsb (%si), %al /* get token */
cmpb $0, %al /* end of string? */
jne 3b
popw %ax
ret
.balign 0x200
这是编译:
/usr/bin/ccache gcc -Os -fno-stack-protector -fno-builtin -nostdinc -DSUPPORT_SERIAL=1 -DSUPPORT_HERCULES=1 -DSUPPORT_GRAPHICS=1 -DHAVE_CONFIG_H -I. -Wall -ggdb3 -Wmissing-prototypes -Wunused -Wshadow -Wpointer-arith -falign-jumps=1 -falign-loops=1 -falign-functions=1 -Wundef -g -c -o ds_teststart_exec-ds_teststart.o ds_test.S
/usr/bin/ccache gcc -g -o ds_teststart.exec -nostdlib -Wl,-N -Wl,-Ttext -Wl,8000 ds_teststart_exec-ds_teststart.o
objcopy -O binary ds_teststart.exec ds_teststart