5

我有代码，从我的 PCIe 驱动程序的 probe() 函数调用（大致基于这篇文章）：

编辑： 根据Andreas Bombe 的回复，我将代码更改为使用pci_iomap()，但我仍然遇到系统挂起的情况

static my_pci_dev pci_dev; /* local structure */
static int pci_setup_region(struct pci_dev *dev)
{
    int bar = 0;

    pci_dev.physical.addr = pci_resource_start(dev, bar);
    pci_dev.physical.size = pci_resource_len(dev, bar);

    pci_dev.virtual.addr = pci_iomap(dev, bar, pci_dev.physical.size);
    if (NULL == pci_dev.virtual.addr) {
        return -ENOMEM;
    } else {
        pci_dev.virtual.size = pci_dev.physical.size;
    }
    printk(KERN_ALERT "Virtual address: %p", pci_dev.virtual.addr);
    if (request_mem_region(pci_dev.physical.addr, pci_dev.physical.size, DEVICE_NAME) == NULL) {
        pci_release_resources();
        return -EBUSY;
    } else {
        pci_dev.physical.allocated = 1;
    }

    /* Test it out! */
    printk(KERN_ALERT "Trying to read data.\n");
    printk(KERN_ALERT "Copied chip-id data:%08x", ioread8(pci_dev.virtual.addr));
    return 0;
}

但是内核只是挂在对ioread8().

难道我做错了什么？还是我需要看硬件？

这是系统干净启动时的输出lspci -v和cat /proc/iomem：

root@socfpga:~# lspci -v
00:00.0 PCI bridge: Altera Corporation Device e000 (rev 01) (prog-if 00 [Normal decode])
    Flags: fast devsel
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 00000000-00000fff
    Memory behind bridge: c0000000-c00fffff
    Prefetchable memory behind bridge: 00000000-000fffff
    Capabilities: [50] MSI: Enable- Count=1/4 Maskable- 64bit+
    Capabilities: [78] Power Management version 3
    Capabilities: [80] Express Root Port (Slot-), MSI 00
    Capabilities: [100] Virtual Channel
    Capabilities: [200] Vendor Specific Information: ID=1172 Rev=0 Len=044 <?>

01:00.0 Multimedia audio controller: Altera Corporation Device e002 (rev 01)
    Subsystem: Altera Corporation Device e002
    Flags: fast devsel, IRQ 75
    Memory at c0000000 (32-bit, non-prefetchable) [disabled] [size=128K]
    Capabilities: [50] MSI: Enable- Count=1/4 Maskable- 64bit+
    Capabilities: [78] Power Management version 3
    Capabilities: [80] Express Endpoint, MSI 00
    Capabilities: [100] Virtual Channel
    Capabilities: [200] Vendor Specific Information: ID=1172 Rev=0 Len=044 <?>
    Kernel modules: test-pci

内存出现[disabled]：我必须启用它吗？

root@socfpga:~# cat /proc/iomem 
00000000-3fffffff : System RAM
  00008000-006fa7d3 : Kernel code
  00754000-007d8c23 : Kernel data
c0000000-cfffffff : ALTERA PCIE RP MEM
  c0000000-c00fffff : PCI Bus 0000:01
    c0000000-c001ffff : 0000:01:00.0
d0000000-dfffffff : ALTERA PCIE RP PREF MEM
ff200000-ff20000f : csr
ff200010-ff20008f : vector_slave
ff210000-ff21003f : ff210000.chipidbridge0
ff280000-ff283fff : Cra
ff702000-ff703fff : /soc/ethernet@ff702000
ff704000-ff704fff : /soc/dwmmc0@ff704000
ff705000-ff705fff : ff705000.spi
ffa00000-ffa00fff : ff705000.spi
ffb40000-ffb4fffe : /soc/usb@ffb40000
ffc00000-ffc00fff : c_can_platform
ffc02000-ffc0201f : serial
ffc04000-ffc04fff : /soc/i2c@ffc04000
ffd02000-ffd02fff : /soc/wd@ffd02000
ffe01000-ffe01fff : /soc/amba/pdma@ffe01000
fff00000-fff00fff : fff00000.spi
ffff0000-ffffffff : /soc/sram@ffff0000
root@socfpga:~#
4

2 回答 2

9

您绝对必须启用它。这些是基本步骤：

pci_enable_device(dev);
pci_request_regions(dev, "driver/device name");
bar0 = pci_iomap(dev, 0, 0);
x = ioread(bar0 + offset);  /* there you are */

pci_*所有调用都需要进行错误检查。如果设备需要做 DMA，你还需要调用pci_set_master和pci_set_dma_mask。

详细地说，绕过 PCI 内核代码并直接对 BAR 进行 ioremapping 可能在很久以前就已经奏效了。我不确定它在当前代码中是否合法，但它肯定是不可取的。

于 2014-05-01T23:33:46.367 回答
2

要启用内存，您可以直接尝试以下命令。

setpci -s <BUS_ADDR> COMMAND=0x02 -s : Used for device selection COMMAND : Asks for the word-sized command register, 0x02 is to enable memory

lspci Output : 0000:01:00.0 RAM memory: Xilinx Corporation Default PCIe endpoint ID 0001:02:00.0 Memory controller: Xilinx Corporation Device 8011 Example : setpci -s 0001:02:00.0 COMMAND=0x02

于 2018-06-12T07:05:49.647 回答