寻找用于构建使用协议缓冲区的项目的 autoconf 和 automake 规则的一个很好的示例,将 protoc 添加到构建过程的最佳方式?
问问题
5190 次
2 回答
17
configure.ac
就 protobuf 库而言,它使用pkg-config
,因此最好使用PKG_CHECK_MODULES
宏来引用它:
PKG_CHECK_MODULES(PROTOBUF, protobuf >= 2.4.0)
AC_SUBST(PROTOBUF_LIBS)
AC_SUBST(PROTOBUF_CFLAGS)
AC_SUBST(PROTOBUF_VERSION)
并检查protoc
路径中的命令。这是一个非常基本的检查它是否在路径中:
AC_CHECK_PROG([PROTOC], [protoc], [protoc])
AS_IF([test "x${PROTOC}" == "x"],
[AC_MSG_ERROR([ProtoBuf compiler "protoc" not found.])])
protoc
或者,允许用户使用--with-protoc=/path/to/protoc
或使用环境变量指定不同的PROTOC
:
# ProtoBuf compiler.
# First, specify with --with-protoc=/path/of/protoc.
# Or, specify with env variable PROTOC.
# If neither of the above, find it in the path.
#AC_MSG_CHECKING([for ProtoBuf compiler protoc])
AC_ARG_WITH([protoc],
[AS_HELP_STRING([--with-protoc=/path/of/protoc],
[Location of the protocol buffers compiler protoc. Defaults to looking on path.])],
[PROTOC="$withval"],
[ AS_IF([test "x${PROTOC}" == "x"],
[AC_PATH_PROG([PROTOC], [protoc], [no])])
]
)
#AC_MSG_RESULT([${PROTOC}])
AS_IF([test "${PROTOC}" == "no"], [AC_MSG_ERROR([ProtoBuf compiler "protoc" not found.])])
Makefile.am
添加规则以构建proto
文件:
%.pb.cc %.pb.h: %.proto
$(PROTOC) --proto_path=$(srcdir) --cpp_out=$(builddir) $^
用 . 指定 protobuf 源文件dist_noinst_DATA
。这对于确保将它们捆绑在.tar.gz
使用make dist
.
dist_noinst_DATA = whatever.proto
(注意:对于较新版本的 autoconf/automake,可能需要使用@builddir@
而不是$(builddir)
.)
nodist_
使用前缀和$(builddir)
路径指定生成的文件:
nodist_myprog_SOURCES = $(builddir)/whatever.pb.cc $(builddir)/whatever.pb.h
并用以下方法清洁它们make clean
:
MOSTLYCLEANFILES = whatever.pb.cc whatever.pb.h
用于BUILT_SOURCES
处理构建的头文件的依赖关系:
BUILT_SOURCES = whatever.pb.h
您的编译器标志可能需要参考构建目录来查找头文件(在 VPATH 构建中工作):
AM_CPPFLAGS += -I$(builddir)
于 2013-08-20T07:09:25.983 回答
7
这似乎有效:
配置.ac:
AC_ARG_WITH([protobuf-libdir],
[AS_HELP_STRING([--with-protobuf-libdir=LIB_DIR],
[location of the protocol buffers libraries, defaults to /usr/lib])],
[PROTOBUF_LIBDIR="$withval"],
[PROTOBUF_LIBDIR='/usr/lib'])
AC_SUBST([PROTOBUF_LIBDIR])
LDFLAGS="$LDFLAGS -L$PROTOBUF_LIBDIR"
AC_CHECK_LIB([protobuf], [main], [], [AC_MSG_ERROR([cannot find protobuf library])])
AC_ARG_WITH([protoc],
[AS_HELP_STRING([--with-protoc=PATH],
[location of the protoc protocol buffer compiler binary, defaults to protoc])],
[PROTOC="$withval"],
[PROTOC='protoc'])
AC_SUBST([PROTOC])
生成文件.am:
%.pb.cc %.pb.h: %.proto
$(PROTOC) --proto_path=$(dir $^) --cpp_out=$(dir $^) $^
然后将 .pb.cc 文件添加到 SOURCES。
于 2012-12-19T00:31:59.993 回答