我想知道是否有人找到了一种方法来确定主控与 stm32f40x 芯片通信的意图？从stm32f40x芯片上的固件来看，主控发送的ADDRess是不可用的，其中包含的r/w位（地址的第0位）也是不可用的。那么如何防止碰撞呢？有没有其他人处理过这个？如果是这样，您使用了哪些技术？我的暂定解决方案如下供参考。我延迟了对 DR 数据寄存器的任何写入，直到发生 TXE 中断。起初我认为这为时已晚，一个字节的垃圾会被淘汰，但它似乎正在工作。
static inline void LLEVInterrupt(uint16_t irqSrc)
{
uint8_t i;
volatile uint16_t status;
I2CCBStruct* buffers;
I2C_TypeDef* addrBase;
// see which IRQ occurred, process accordingly...
switch (irqSrc)
{
case I2C_BUS_CHAN_1:
addrBase = this.addrBase1;
buffers = &this.buffsBus1;
break;
case I2C_BUS_CHAN_2:
addrBase = this.addrBase2;
buffers = &this.buffsBus2;
break;
case I2C_BUS_CHAN_3:
addrBase = this.addrBase3;
buffers = &this.buffsBus3;
break;
default:
while(1);
}
// ...START condition & address match detected
if (I2C_GetITStatus(addrBase, I2C_IT_ADDR) == SET)
{
// I2C_IT_ADDR: Cleared by software reading SR1 register followed reading SR2, or by hardware
// when PE=0.
// Note: Reading I2C_SR2 after reading I2C_SR1 clears the ADDR flag, even if the ADDR flag was
// set after reading I2C_SR1. Consequently, I2C_SR2 must be read only when ADDR is found
// set in I2C_SR1 or when the STOPF bit is cleared.
status = addrBase->SR1;
status = addrBase->SR2;
// Reset the index and receive count
buffers->txIndex = 0;
buffers->rxCount = 0;
// setup to ACK any Rx'd bytes
I2C_AcknowledgeConfig(addrBase, ENABLE);
return;
}
// Slave receiver mode
if (I2C_GetITStatus(addrBase, I2C_IT_RXNE) == SET)
{
// I2C_IT_RXNE: Cleared by software reading or writing the DR register
// or by hardware when PE=0.
// copy the received byte to the Rx buffer
buffers->rxBuf[buffers->rxCount] = (uint8_t)I2C_ReadRegister(addrBase, I2C_Register_DR);
if (RX_BUFFER_SIZE > buffers->rxCount)
{
buffers->rxCount++;
}
return;
}
// Slave transmitter mode
if (I2C_GetITStatus(addrBase, I2C_IT_TXE) == SET)
{
// I2C_IT_TXE: Cleared by software writing to the DR register or
// by hardware after a start or a stop condition or when PE=0.
// send any remaining bytes
I2C_SendData(addrBase, buffers->txBuf[buffers->txIndex]);
if (buffers->txIndex < buffers->txCount)
{
buffers->txIndex++;
}
return;
}
// ...STOP condition detected
if (I2C_GetITStatus(addrBase, I2C_IT_STOPF) == SET)
{
// STOPF (STOP detection) is cleared by software sequence: a read operation
// to I2C_SR1 register (I2C_GetITStatus()) followed by a write operation to
// I2C_CR1 register (I2C_Cmd() to re-enable the I2C peripheral).
// From the reference manual RM0368:
// Figure 163. Transfer sequence diagram for slave receiver
// if (STOPF == 1) {READ SR1; WRITE CR1}
// clear the IRQ status
status = addrBase->SR1;
// Write to CR1
I2C_Cmd(addrBase, ENABLE);
// read cycle (reset the status?
if (buffers->txCount > 0)
{
buffers->txCount = 0;
buffers->txIndex = 0;
}
// write cycle begun?
if (buffers->rxCount > 0)
{
// pass the I2C data to the enabled protocol handler
for (i = 0; i < buffers->rxCount; i++)
{
#if (COMM_PROTOCOL == COMM_PROTOCOL_DEBUG)
status = ProtProcRxData(buffers->rxBuf[i]);
#elif (COMM_PROTOCOL == COMM_PROTOCOL_PTEK)
status = PTEKProcRxData(buffers->rxBuf[i]);
#else
#error ** Invalid Host Protocol Selected **
#endif
if (status != ST_OK)
{
LogErr(ST_COMM_FAIL, __LINE__);
}
}
buffers->rxCount = 0;
}
return;
}
if (I2C_GetITStatus(addrBase, I2C_IT_AF) == SET)
{
// The NAck received from the host on the last byte of a transmit
// is shown as an acknowledge failure and must be cleared by
// writing 0 to the AF bit in SR1.
// This is not a real error but just how the i2c slave transmission process works.
// The hardware has no way to know how many bytes are to be transmitted, so the
// NAck is assumed to be a failed byte transmission.
// EV3-2: AF=1; AF is cleared by writing ‘0’ in AF bit of SR1 register.
I2C_ClearITPendingBit(addrBase, I2C_IT_AF);
return;
}
if (I2C_GetITStatus(addrBase, I2C_IT_BERR) == SET)
{
// There are extremely infrequent bus errors when testing with I2C Stick.
// Safer to have this check and clear than to risk an
// infinite loop of interrupts
// Set by hardware when the interface detects an SDA rising or falling
// edge while SCL is high, occurring in a non-valid position during a
// byte transfer.
// Cleared by software writing 0, or by hardware when PE=0.
I2C_ClearITPendingBit(addrBase, I2C_IT_BERR);
LogErr(ST_COMM_FAIL, __LINE__);
return;
}
if (I2C_GetITStatus(addrBase, I2C_IT_OVR) == SET)
{
// Check for other errors conditions that must be cleared.
I2C_ClearITPendingBit(addrBase, I2C_IT_OVR);
LogErr(ST_COMM_FAIL, __LINE__);
return;
}
if (I2C_GetITStatus(addrBase, I2C_IT_TIMEOUT) == SET)
{
// Check for other errors conditions that must be cleared.
I2C_ClearITPendingBit(addrBase, I2C_IT_TIMEOUT);
LogErr(ST_COMM_FAIL, __LINE__);
return;
}
// a spurious IRQ occurred; log it
LogErr(ST_INV_STATE, __LINE__);
}